NAME
cgsix
—
Sun accelerated 8-bit color frame
buffer
SYNOPSIS
cgsix* at sbus? slot ? offset ?
(sun4c/sun4m)
cgsix0 at obio0 addr 0xfb000000 level 4
(sun4/300)
cgsix0 at obio0 addr 0x0b000000 level 4
(sun4/100)
DESCRIPTION
Thecgsix
is a memory based color frame buffer. It
supports the minimal ioctl's needed to run
X(7).
There are several versions of the cgsix
board. The Sun part numbers and board types are:
- 501-1374, 501-1532
- P4 GX
- 501-1505
- P4 GX with 3/80 backpanel
- 501-1481, 501-1645
- Sbus double-width GX
- 501-1672, 501-1996
- Sbus GX
- 501-1717, 501-2018, 501-2039
- Sbus GX+
- 501-2325, 501-2922
- Sbus TGX
- 501-2253, 501-2955
- Sbus TGX+
There are also on-board ‘GX’ cards in the ‘SPARCstation IPX’ and ‘SPARCstation LX’ machines.
The ‘GX’ and ‘TGX’ cards have 1Mb of on-board memory and support a maximum graphics resolution of 1152x900. The ‘GX+’ cards have 4Mb of on-board memory and support a maximum resolution of 1280x1024. The ‘TGX+’ cards have 4Mb of on-board memory and support a maximum resolution of 1600x1280. The ‘TGX’ (Turbo GX) cards are faster than the ‘GX’ cards.
The number of supported resolutions varies by card type. All cards support a resolution of 1152x900 at 66Hz. All but the P4 and double-width cards support a resolution of 1152x900 at 76Hz. The cards default to a resolution dependent on the attached monitor (usually 1152x900).
It is only possible to change the resolution of a
cgsix
card from the PROM before the operating system
is loaded. For the primary card, this can be done using the
‘output-device’ PROM field. For example, for a
‘TGX+’ card, the following PROM command will set the
resolution to 1280x1024 at 76Hz:
setenv output-device screen:r1280x1024x76
For secondary cards, a different method must be used to set the resolution. For a machine with OpenBoot 2.x or 3.x, and assuming a ‘TGX’ card at Sbus slot 1, the following PROM commands will set the resolution to 1024x768 at 60Hz:
nvedit probe-all " /iommu/sbus/cgsix@1" select-dev r1024x768x60 " /iommu/sbus/cgsix@1" " set-resolution" execute-device-method device-end install-console banner ^C nvstore setenv use-nvramrc? true reset
For Sun4c machines, the device-path above would be:
" /sbus/cgsix@1"
For Sun-4 and Sun-3 systems, it is only possible to change PROM fields by altering byte values. For these systems, it is probably easier to use the eeprom(8) command to set the scrsize field to the desired resolution.
EXAMPLES
cgsix0 at obio0 addr 0xfb000000 level 4:
cgsix/p4, 1152 x 900, rev 1
cgsix0 at sbus0 slot 0
offset 0x0 level 9: SUNW,501-2325, 1152 x 900, rev 11
cgsix0 at sbus0 slot 0 offset 0x0 level 9: SUNW,501-2253,
1280 x 1024, rev 11
SEE ALSO
sparc/bwtwo(4), sparc/cgeight(4), sparc/cgfour(4), sparc/cgfourteen(4), sparc/cgthree(4), sparc/cgtwo(4), sparc/tcx(4), eeprom(8)
BUGS
The double-width ‘GX’ and the ‘GX+’ cards are not compatible with UltraSPARC machines.
On Sun-4 systems using a P4 GX card as console, the console field in the PROM must be set to p4opt, otherwise the card will not be recognised as the console output device.
Several firmware revisions on cgsix
boards
have a terminal emulation bug that shows up when using the screen control
sequences for inserting blank lines near the bottom end of the screen (i.e.,
the control sequences produced by the termcap ‘al’ and
‘AL’ capabilities found in the
terminfo(5) database). The most likely occasion for triggering this
bug is to use a full-screen editor such as
vi(1)
on the workstation's console.
To work around this you can set your TERM
environment variable to the ‘sun-cgsix’ terminal definition
which is the same as the ‘sun’ entry, except that the
‘al’ and ‘AL’ capabilities have been removed (at
the cost of making the scrolling of the screen slower).