man.bsd.lv manual page server

DESCRIPTION

The following options define the general layout policies:

-E

Erase the content of the disk before making the filesystem. The reserved area in front of the superblock (for bootcode) will not be erased. Erasing is only relevant to flash-memory or thinly provisioned devices. Erasing may take a long time. If the device does not support BIO_DELETE, the command will fail.

-J

Enable journaling on the new file system via gjournal. See gjournal(8) for details.

-L volname

Add a volume label to the new file system.

-N

Cause the file system parameters to be printed out without really creating the file system.

-O filesystem-type

Use 1 to specify that a UFS1 format file system be built; use 2 to specify that a UFS2 format file system be built. The default format is UFS2.

-T disktype

For backward compatibility.

-U

Enable soft updates on the new file system.

-a maxcontig

Specify the maximum number of contiguous blocks that will be laid out before forcing a rotational delay. The default value is 16. See tunefs(8) for more details on how to set this option.

-b block-size

The block size of the file system, in bytes. It must be a power of 2. The default size is 32768 bytes, and the smallest allowable size is 4096 bytes. The optimal block:fragment ratio is 8:1. Other ratios are possible, but are not recommended, and may produce poor results.

-c blocks-per-cylinder-group

The number of blocks per cylinder group in a file system. The default is to compute the maximum allowed by the other parameters. This value is dependent on a number of other parameters, in particular the block size and the number of bytes per inode.

-d max-extent-size

The file system may choose to store large files using extents. This parameter specifies the largest extent size that may be used. The default value is the file system blocksize. It is presently limited to a maximum value of 16 times the file system blocksize and a minimum value of the file system blocksize.

-e maxbpg

Indicate the maximum number of blocks any single file can allocate out of a cylinder group before it is forced to begin allocating blocks from another cylinder group. The default is about one quarter of the total blocks in a cylinder group. See tunefs(8) for more details on how to set this option.

-f frag-size

The fragment size of the file system in bytes. It must be a power of two ranging in value between blocksize/8 and blocksize. The default is 4096 bytes.

-g avgfilesize

The expected average file size for the file system.

-h avgfpdir

The expected average number of files per directory on the file system.

-i bytes

Specify the density of inodes in the file system. The default is to create an inode for every (2 * frag-size) bytes of data space. If fewer inodes are desired, a larger number should be used; to create more inodes a smaller number should be given. One inode is required for each distinct file, so this value effectively specifies the average file size on the file system.

-j

Enable soft updates journaling on the new file system. This flag is implemented by running the tunefs(8) utility found in the user's $PATH.

-k held-for-metadata-blocks

Set the amount of space to be held for metadata blocks in each cylinder group. When set, the file system preference routines will try to save the specified amount of space immediately following the inode blocks in each cylinder group for use by metadata blocks. Clustering the metadata blocks speeds up random file access and decreases the running time of fsck(8). By default newfs sets it to half of the space reserved to minfree.

-l

Enable multilabel MAC on the new file system.

-m free-space

The percentage of space reserved from normal users; the minimum free space threshold. The default value used is defined by MINFREE from <ufs/ffs/fs.h>, currently 8%. See tunefs(8) for more details on how to set this option.

-n

Do not create a .snap directory on the new file system. The resulting file system will not support snapshot generation, so dump(8) in live mode and background fsck(8) will not function properly. The traditional fsck(8) and offline dump(8) will work on the file system. This option is intended primarily for memory or vnode-backed file systems that do not require dump(8) or fsck(8) support.

-o optimization

(space or time). The file system can either be instructed to try to minimize the time spent allocating blocks, or to try to minimize the space fragmentation on the disk. If the value of minfree (see above) is less than 8%, the default is to optimize for space; if the value of minfree is greater than or equal to 8%, the default is to optimize for time. See tunefs(8) for more details on how to set this option.

-p partition

The partition name (a..h) you want to use in case the underlying image is a file, so you do not have access to individual partitions through the filesystem. Can also be used with a device, e.g., newfs -p f /dev/da1s3 is equivalent to newfs /dev/da1s3f.

-r reserved

The size, in sectors, of reserved space at the end of the partition specified in special. This space will not be occupied by the file system; it can be used by other consumers such as geom(4). Defaults to 0.

-s size

The size of the file system in sectors. This value defaults to the size of the raw partition specified in special less the reserved space at its end (see -r). A size of 0 can also be used to choose the default value. A valid size value cannot be larger than the default one, which means that the file system cannot extend into the reserved space.

-t

Turn on the TRIM enable flag. If enabled, and if the underlying device supports the BIO_DELETE command, the file system will send a delete request to the underlying device for each freed block. The trim enable flag is typically set for flash-memory devices to reduce write amplification which reduces wear on write-limited flash-memory and often improves long-term performance. Thinly provisioned storage also benefits by returning unused blocks to the global pool.

The following options override the standard sizes for the disk geometry. Their default values are taken from the disk label. Changing these defaults is useful only when using newfs to build a file system whose raw image will eventually be used on a different type of disk than the one on which it is initially created (for example on a write-once disk). Note that changing any of these values from their defaults will make it impossible for fsck(8) to find the alternate superblocks if the standard superblock is lost.

-S sector-size

The size of a sector in bytes (almost never anything but 512).