man.bsd.lv manual page server

DESCRIPTION

F_DUPFD

Return a new descriptor as follows:

• Lowest numbered available descriptor greater than or equal to arg.
• Same object references as the original descriptor.
• New descriptor shares the same file offset if the object was a file.
• Same access mode (read, write or read/write).
• Same file status flags (i.e., both file descriptors share the same file status flags).
• The close-on-exec flag associated with the new file descriptor is set to remain open across execv(2) system calls.

F_GETFD

Get the close-on-exec flag associated with the file descriptor fd. If the low-order bit of the returned value is 0, the file will remain open across exec(), otherwise the file will be closed upon execution of exec() (arg is ignored).

F_SETFD

Set the close-on-exec flag associated with fd to the low order bit of arg (0 or 1 as above).

F_GETFL

Get descriptor status flags, as described below (arg is ignored).

F_SETFL

Set descriptor status flags to arg.

F_GETOWN

Get the process ID or process group currently receiving SIGIO and SIGURG signals; process groups are returned as negative values (arg is ignored).

F_SETOWN

Set the process or process group to receive SIGIO and SIGURG signals; process groups are specified by supplying arg as negative, otherwise arg is interpreted as a process ID.

The flags for the F_GETFL and F_SETFL flags are as follows:

O_NONBLOCK

Non-blocking I/O; if no data is available to a read call, or if a write operation would block, the read or write call returns -1 with the error EAGAIN.

O_APPEND

Force each write to append at the end of file; corresponds to the O_APPEND flag of open(2).

O_ASYNC

Enable the SIGIO signal to be sent to the process group when I/O is possible, e.g., upon availability of data to be read.

Several commands are available for doing advisory file locking; they all operate on the following structure:

struct flock {
	off_t	l_start;	/* starting offset */
	off_t	l_len;		/* len = 0 means until end of file */
	pid_t	l_pid;		/* lock owner */
	short	l_type;		/* lock type: read/write, etc. */
	short	l_whence;	/* type of l_start */
};

F_GETLK

Get the first lock that blocks the lock description pointed to by the third argument, arg, taken as a pointer to a struct flock (see above). The information retrieved overwrites the information passed to fcntl in the flock structure. If no lock is found that would prevent this lock from being created, the structure is left unchanged by this function call except for the lock type which is set to F_UNLCK.

F_SETLK

Set or clear a file segment lock according to the lock description pointed to by the third argument, arg, taken as a pointer to a struct flock (see above). F_SETLK is used to establish shared (or read) locks (F_RDLCK) or exclusive (or write) locks, (F_WRLCK), as well as remove either type of lock (F_UNLCK). If a shared or exclusive lock cannot be set, fcntl returns immediately with EACCES.

F_SETLKW

This command is the same as F_SETLK except that if a shared or exclusive lock is blocked by other locks, the process waits until the request can be satisfied. If a signal that is to be caught is received while fcntl is waiting for a region, the fcntl will be interrupted if the signal handler has not specified the SA_RESTART (see sigaction(2)).

When a shared lock has been set on a segment of a file, other processes can set shared locks on that segment or a portion of it. A shared lock prevents any other process from setting an exclusive lock on any portion of the protected area. A request for a shared lock fails if the file descriptor was not opened with read access.

An exclusive lock prevents any other process from setting a shared lock or an exclusive lock on any portion of the protected area. A request for an exclusive lock fails if the file was not opened with write access.

The value of l_whence is SEEK_SET, SEEK_CUR, or SEEK_END to indicate that the relative offset, l_start bytes, will be measured from the start of the file, current position, or end of the file, respectively. The value of l_len is the number of consecutive bytes to be locked. If l_len is negative, the result is undefined. The l_pid field is only used with F_GETLK to return the process ID of the process holding a blocking lock. After a successful F_GETLK request, the value of l_whence is SEEK_SET.

Locks may start and extend beyond the current end of a file, but may not start or extend before the beginning of the file. A lock is set to extend to the largest possible value of the file offset for that file if l_len is set to zero. If l_whence and l_start point to the beginning of the file, and l_len is zero, the entire file is locked. If an application wishes only to do entire file locking, the flock(2) system call is much more efficient.

There is at most one type of lock set for each byte in the file. Before a successful return from an F_SETLK or an F_SETLKW request when the calling process has previously existing locks on bytes in the region specified by the request, the previous lock type for each byte in the specified region is replaced by the new lock type. As specified above under the descriptions of shared locks and exclusive locks, an F_SETLK or an F_SETLKW request fails or blocks respectively when another process has existing locks on bytes in the specified region and the type of any of those locks conflicts with the type specified in the request.

This interface follows the completely stupid semantics of System V and IEEE Std 1003.1-1988 (“POSIX.1”) that require that all locks associated with a file for a given process are removed when any file descriptor for that file is closed by that process. This semantic means that applications must be aware of any files that a subroutine library may access. For example if an application for updating the password file locks the password file database while making the update, and then calls getpwname(3) to retrieve a record, the lock will be lost because getpwname(3) opens, reads, and closes the password database. The database close will release all locks that the process has associated with the database, even if the library routine never requested a lock on the database. Another minor semantic problem with this interface is that locks are not inherited by a child process created using the fork(2) function. The flock(2) interface has much more rational last close semantics and allows locks to be inherited by child processes. Flock(2) is recommended for applications that want to ensure the integrity of their locks when using library routines or wish to pass locks to their children. Note that flock(2) and fcntl(2) locks may be safely used concurrently.

All locks associated with a file for a given process are removed when the process terminates.

A potential for deadlock occurs if a process controlling a locked region is put to sleep by attempting to lock the locked region of another process. This implementation detects that sleeping until a locked region is unlocked would cause a deadlock and fails with an EDEADLK error.