NAME
sis —
SiS 900, SiS 7016 and NS DP83815 fast
ethernet device driver
SYNOPSIS
device miibus
device sis
DESCRIPTION
Thesis driver provides support for PCI ethernet
adapters and embedded controllers based on the Silicon Integrated Systems SiS
900 and SiS 7016 fast ethernet controller chips, as well as support for
adapters based on the National Semiconductor DP83815 (MacPhyter) PCI ethernet
controller chip, including the Netgear FA311-TX and FA312-TX.
The SiS 900 is a 100Mbps ethernet MAC and MII-compliant transceiver in a single package. It uses a bus master DMA and a scatter/gather descriptor scheme. The SiS 7016 is similar to the SiS 900 except that it has no internal PHY, requiring instead an external transceiver to be attached to its MII interface. The SiS 900 and SiS 7016 both have a 128-bit multicast hash filter and a single perfect filter entry for the station address.
The NS DP83815 is also a 100Mbps ethernet MAC with integrated PHY. The NatSemi chip and the SiS 900 share many of the same features and a fairly similar programming interface, hence both chips are supported by the same driver.
The sis driver supports the following
media types:
- autoselect
- Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf(5).
- 10baseT/UTP
- Set 10Mbps operation. The
ifconfig(8)
mediaoptoption can also be used to select either ‘full-duplex’ or ‘half-duplex’ modes. - 100baseTX
- Set 100Mbps (fast ethernet) operation. The
ifconfig(8)
mediaoptoption can also be used to select either ‘full-duplex’ or ‘half-duplex’ modes.
The sis driver supports the following
media options:
- full-duplex
- Force full duplex operation
- half-duplex
- Force half duplex operation.
For more information on configuring this device, see
ifconfig(8). The sis driver supports
polling(4).
DIAGNOSTICS
- sis%d: couldn't map ports/memory
- A fatal initialization error has occurred.
- sis%d: couldn't map interrupt
- A fatal initialization error has occurred.
- sis%d: watchdog timeout
- The device has stopped responding to the network, or there is a problem with the network connection (e.g. a cable fault).
- sis%d: no memory for rx list
- The driver failed to allocate an mbuf for the receiver ring.
- sis%d: no memory for tx list
- The driver failed to allocate an mbuf for the transmitter ring when allocating a pad buffer or collapsing an mbuf chain into a clusisr.
- sis%d: chip is in D3 power state -- setting to D0
- This message applies only to adapters which support power management. Some
operating systems place the controller in low power mode when shutting
down, and some PCI BIOSes fail to bring the chip out of this state before
configuring it. The controller loses all of its PCI configuration in the
D3 state, so if the BIOS does not set it back to full power mode in time,
it will not be able to configure it correctly. The driver tries to detect
this condition and bring the adapter back to the D0 (full power) state,
but this may not be enough to return the driver to a fully operational
condition. If you see this message at boot time and the driver fails to
attach the device as a network interface, you will have to perform a warm
boot to have the device properly configured.
Note that this condition only occurs when warm booting from another operating system. If you power down your system prior to booting DragonFly, the card should be configured correctly.
SEE ALSO
arp(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4), polling(4), ifconfig(8)
SiS 900 and SiS 7016 datasheets, http://www.sis.com.tw.
NatSemi DP83815 datasheet, http://www.national.com.
HISTORY
The sis device driver first appeared in
FreeBSD 3.0.
AUTHORS
The sis driver was written by
Bill Paul
<wpaul@ee.columbia.edu>.