man.bsd.lv manual page server

Manual Page Search Parameters
SIS(4) Device Drivers Manual SIS(4)

sisSiS 900, SiS 7016 and NS DP83815 fast ethernet device driver

device miibus
device sis

The sis driver provides support for PCI ethernet adapters and embedded controllers based on the Silicon Integrated Systems SiS 900 and SiS 7016 fast ethernet controller chips, as well as support for adapters based on the National Semiconductor DP83815 (MacPhyter) PCI ethernet controller chip, including the Netgear FA311-TX and FA312-TX.

The SiS 900 is a 100Mbps ethernet MAC and MII-compliant transceiver in a single package. It uses a bus master DMA and a scatter/gather descriptor scheme. The SiS 7016 is similar to the SiS 900 except that it has no internal PHY, requiring instead an external transceiver to be attached to its MII interface. The SiS 900 and SiS 7016 both have a 128-bit multicast hash filter and a single perfect filter entry for the station address.

The NS DP83815 is also a 100Mbps ethernet MAC with integrated PHY. The NatSemi chip and the SiS 900 share many of the same features and a fairly similar programming interface, hence both chips are supported by the same driver.

The sis driver supports the following media types:

autoselect
Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media options to rc.conf(5).
10baseT/UTP
Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either ‘full-duplex’ or ‘half-duplex’ modes.
100baseTX
Set 100Mbps (fast ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either ‘full-duplex’ or ‘half-duplex’ modes.

The sis driver supports the following media options:

full-duplex
Force full duplex operation
half-duplex
Force half duplex operation.

For more information on configuring this device, see ifconfig(8). The sis driver supports polling(4).

sis%d: couldn't map ports/memory
A fatal initialization error has occurred.
sis%d: couldn't map interrupt
A fatal initialization error has occurred.
sis%d: watchdog timeout
The device has stopped responding to the network, or there is a problem with the network connection (e.g. a cable fault).
sis%d: no memory for rx list
The driver failed to allocate an mbuf for the receiver ring.
sis%d: no memory for tx list
The driver failed to allocate an mbuf for the transmitter ring when allocating a pad buffer or collapsing an mbuf chain into a clusisr.
sis%d: chip is in D3 power state -- setting to D0
This message applies only to adapters which support power management. Some operating systems place the controller in low power mode when shutting down, and some PCI BIOSes fail to bring the chip out of this state before configuring it. The controller loses all of its PCI configuration in the D3 state, so if the BIOS does not set it back to full power mode in time, it will not be able to configure it correctly. The driver tries to detect this condition and bring the adapter back to the D0 (full power) state, but this may not be enough to return the driver to a fully operational condition. If you see this message at boot time and the driver fails to attach the device as a network interface, you will have to perform a warm boot to have the device properly configured.

Note that this condition only occurs when warm booting from another operating system. If you power down your system prior to booting DragonFly, the card should be configured correctly.

arp(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4), polling(4), ifconfig(8)

SiS 900 and SiS 7016 datasheets, http://www.sis.com.tw.

NatSemi DP83815 datasheet, http://www.national.com.

The sis device driver first appeared in FreeBSD 3.0.

The sis driver was written by Bill Paul <wpaul@ee.columbia.edu>.

September 4, 1999 DragonFly-5.6.1