man.bsd.lv manual page server

Manual Page Search Parameters
BNX(4) Device Drivers Manual BNX(4)

bnx — Broadcom BCM57785/BCM5718 families 10/100/Gigabit Ethernet device

device miibus
device bnx

Alternatively, to load the driver as a module at boot time, place the following line in /boot/loader.conf:

if_bnx_load="YES"

The bnx driver supports the PCIe Ethernet adapters based on Broadcom BCM57785/BCM5718 families chips.

The following features are supported in the bnx driver:

By default, the bnx driver will try enabling as many reception queues as are allowed by the number of CPUs in the system. For BCM5717C, BCM5719 and BCM5720, in addition to the reception queues, by default, the bnx driver will try enabling as many transmission queues as are allowed by the number of CPUs in the system and the number of enabled reception queues. If multiple transmission queues are enabled, the round-robin arbitration is performed among the transmission queues. It should be noted that if both TSO and multiple transmission queues are enabled, the round-robin arbitration between transmission queues is done at the TSO packet boundary.

The bnx driver supports the following media types:

Enable autoselection of the media types and options

Set 10Mbps operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.

Set 100Mbps (Fast Ethernet) operation. The mediaopt option can also be used to select either full-duplex or half-duplex modes.

Set 1000Mbps (Gigabit Ethernet) operation. The mediaopt option can only be set full-duplex mode.

The bnx driver supports the following media options:

Force full duplex operation.

Force half duplex operation.

Note that the 1000baseT media type is only available if it is supported by the adapter. For more information on configuring this device, see ifconfig(8). The bnx driver supports polling(4).

The bnx driver supports Gigabit Ethernet adapters and Fast Ethernet adapters based on the Broadcom BCM57785/BCM5718 families chips:

X is the device unit number.

hw.bnx.rx_rings hw.bnxX.rx_rings
If MSI-X is used, this tunable specifies the number of reception queues to be enabled. Maximum allowed value for these tunables is 4 and it must be power of 2 aligned. Setting these tunables to 0 allows the driver to enable as many reception queues as allowed by the number of CPUs.
hw.bnx.tx_rings hw.bnxX.tx_rings
For BCM5717C, BCM5719 and BCM5720, if MSI-X is used, this tunable specifies the number of transmission queues to be enabled. Maximum allowed value for these tunables is 4, it must be power of 2 aligned and it must be less than or equal to the number of reception queues enabled. Setting these tunables to 0 allows the driver to enable as many transmission queues as allowed by the number of CPUs and number reception queues enabled.
hw.bnx.msix.enable hw.bnxX.msix.enable
By default, the driver will use MSI-X if it is supported. This behaviour can be turned off by setting this tunable to 0.
hw.bnx.msi.enable hw.bnxX.msi.enable
If MSI-X is disabled and MSI is supported, the driver will use MSI. This behavior can be turned off by setting this tunable to 0.
hw.bnxX.msi.cpu
If MSI is used, it specifies the MSI's target CPU.

A number of per-interface variables are implemented in the dev.bnx.X branch of the sysctl(3) MIB.

rx_rings
Number of reception queues enabled (read-only). Use the tunable hw.bnx.rx_rings or hw.bnxX.rx_rings to configure it.
tx_rings
Number of transmission queues enabled (read-only). Use the tunable hw.bnx.tx_rings or hw.bnxX.tx_rings to configure it.
rx_coal_ticks
How often status block should be updated and interrupt should be generated by the device, due to receiving packets. It is used together with rx_coal_bds to achieve RX interrupt moderation. Default value is 150 (microseconds).
tx_coal_ticks
How often status block should be updated and interrupt should be generated by the device, due to sending packets. It is used together with tx_coal_bds to achieve TX interrupt moderation. Default value is 1023 (microseconds).
rx_coal_bds
Maximum number of BDs which must be received by the device before the device updates the status block and generates interrupt. It is used together with rx_coal_ticks to achieve RX interrupt moderation. Default value is 0 (disabled).
rx_coal_bds_poll
Maximum number of BDs which must be received by the device before the device updates the status block during polling(4). It is used together with rx_coal_ticks to reduce the frequency of status block updating due to RX. Default value is 32.
tx_coal_bds
Maximum number of sending BDs which must be processed by the device before the device updates the status block and generates interrupt. It is used together with tx_coal_ticks to achieve TX interrupt moderation. Default value is 128.
tx_coal_bds_poll
Maximum number of sending BDs which must be processed by the device before the device updates the status block during polling(4). It is used together with tx_coal_ticks to reduce the frequency of status block updating due to TX. Default value is 64.
force_defrag
Force defragment the sending mbuf chains, if the mbuf chain is not a TSO segment and contains more than 1 mbufs. This improves transmission performance on certain low end chips, however, this also increases CPU load. Default value is 0 (disabled).
tx_wreg
The number of transmission descriptors should be setup before the hardware register is written. Setting this value too high will have negative effect on transmission timeliness. Setting this value too low will hurt overall transmission performance due to the frequent hardware register writing. Default value is 8.
std_refill
Number of packets should be received before the standard reception producer ring is refilled. Setting this value too low will cause extra thread scheduling cost. Setting this value too high will make chip drop incoming packets. Default value is 128 / number of reception queues.
rx_coal_bds_int
Maximum number of BDs which must be received by the device before the device updates the status block during host interrupt processing. Default value is 80.
tx_coal_bds_int
Maximum number of sending BDs which must be processed by the device before the device updates the status block during host interrupt processing. Default value is 64.
norxbds
Number of times the standard reception producer ring is short of reception BDs. If this value grows fast, it is usually an indication that std_refill is set too high.
errors
Number of errors, both critical and non-critical, happened.

arp(4), bge(4), ifmedia(4), miibus(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)

The bnx device driver first appeared in DragonFly 3.1.

The bnx driver was based on bge(4) written by Bill Paul <wpaul@windriver.com>. Sepherosa Ziehau added receive side scaling, multiple transmission queues and multiple MSI-X support to DragonFly.

May 13, 2017 DragonFly-5.6.1