man.bsd.lv manual page server

Manual Page Search Parameters
ICMP(4) Device Drivers Manual ICMP(4)

icmp — Internet Control Message Protocol

#include <sys/socket.h>
#include <netinet/in.h>

int
socket(AF_INET, SOCK_RAW, proto);

ICMP is the error and control message protocol used by IP and the Internet protocol family. It may be accessed through a “raw socket” for network monitoring and diagnostic functions. The proto parameter to the socket call to create an ICMP socket is obtained from getprotobyname(3). ICMP sockets are connectionless, and are normally used with the sendto(2) and recvfrom(2) calls, though the connect(2) call may also be used to fix the destination for future packets (in which case the read(2) or recv(2) and write(2) or send(2) system calls may be used).

Outgoing packets automatically have an IP header prepended to them (based on the destination address). Incoming packets are received with the IP header and options intact.

ICMP messages are classified according to the type and code fields present in the ICMP header. The abbreviations for the types and codes may be used in rules in pf.conf(5). The following types are defined:

0 echorep Echo reply
3 unreach Destination unreachable
4 squench Packet loss, slow down
5 redir Shorter route exists
6 althost Alternate host address
8 echoreq Echo request
9 routeradv Router advertisement
10 routersol Router solicitation
11 timex Time exceeded
12 paramprob Invalid IP header
13 timereq Timestamp request
14 timerep Timestamp reply
15 inforeq Information request
16 inforep Information reply
17 maskreq Address mask request
18 maskrep Address mask reply
30 trace Traceroute
31 dataconv Data conversion problem
32 mobredir Mobile host redirection
33 ipv6-where IPv6 where-are-you
34 ipv6-here IPv6 i-am-here
35 mobregreq Mobile registration request
36 mobregrep Mobile registration reply
39 skip SKIP
40 photuris Photuris

The following codes are defined:

0 net-unr unreach Network unreachable
1 host-unr unreach Host unreachable
2 proto-unr unreach Protocol unreachable
3 port-unr unreach Port unreachable
4 needfrag unreach Fragmentation needed but DF bit set
5 srcfail unreach Source routing failed
6 net-unk unreach Network unknown
7 host-unk unreach Host unknown
8 isolate unreach Host isolated
9 net-prohib unreach Network administratively prohibited
10 host-prohib unreach Host administratively prohibited
11 net-tos unreach Invalid TOS for network
12 host-tos unreach Invalid TOS for host
13 filter-prohib unreach Prohibited access
14 host-preced unreach Precedence violation
15 cutoff-preced unreach Precedence cutoff
0 redir-net redir Shorter route for network
1 redir-host redir Shorter route for host
2 redir-tos-net redir Shorter route for TOS and network
3 redir-tos-host redir Shorter route for TOS and host
0 normal-adv routeradv Normal advertisement
16 common-adv routeradv Selective advertisement
0 transit timex Time exceeded in transit
1 reassemb timex Time exceeded in reassembly
0 badhead paramprob Invalid option pointer
1 optmiss paramprob Missing option
2 badlen paramprob Invalid length
1 unknown-ind photuris Unknown security index
2 auth-fail photuris Authentication failed
3 decrypt-fail photuris Decryption failed

A socket operation may fail with one of the following errors returned:

[EISCONN]
when trying to establish a connection on a socket which already has one, or when trying to send a datagram with the destination address specified and the socket is already connected;
[ENOTCONN]
when trying to send a datagram, but no destination address is specified, and the socket hasn't been connected;
[ENOBUFS]
when the system runs out of memory for an internal data structure;
[EADDRNOTAVAIL]
when an attempt is made to create a socket with a network address for which no network interface exists.

recv(2), send(2), inet(4), ip(4), netintro(4)

The icmp protocol appeared in 4.3BSD.

September 10, 2015 OpenBSD-7.0