man.bsd.lv manual page server

DESCRIPTION

In the first synopsis, RAID controllers are managed. device specifies either a drive (e.g. sd0) or a RAID controller (e.g. ami0). For operations which will be performed against ses(4) or safte(4) enclosures, it is also possible to directly specify the enclosure name (e.g. safte0).

In the second synopsis, softraid(4) volumes are managed. device specifies either a volume (e.g. sd0) or the softraid(4) controller (always softraid0).

The options for RAID controllers are as follows:

-a alarm-function

Control the RAID card's alarm functionality, if supported. alarm-function may be one of:

disable

Disable the alarm on the RAID controller.

enable

Enable the alarm on the RAID controller.

get

Retrieve the current alarm state (enabled or disabled).

silence | quiet

Silence the alarm if it is currently beeping.

The alarm-function may be specified as given above, or by the first letter only (e.g. -a e).

-b channel:target[.lun]

Instruct the device at channel:target[.lun] to start blinking, if there is ses(4) or safte(4) support in the enclosure.

-H channel:target[.lun]

If the device at channel:target[.lun] is currently marked “Unused”, promote it to being a “Hot Spare”.

-h

Where necessary, produce “human-readable” output. Use unit suffixes: Byte, Kilobyte, Megabyte, Gigabyte, Terabyte, Petabyte, Exabyte in order to reduce the number of digits to four or less.

-i

Enumerate the selected RAID devices. This is the default if no other option is given.

-q

Show vendor, product, revision, and serial number for the given disk.

-R chunk | channel:target[.lun]

Manually kick off a rebuild of a degraded RAID volume, using chunk or channel:target[.lun] as a new chunk (with softraid(4), a partition of fstype “RAID”), replacing the offline chunk in the volume; it is not possible to change the number of chunks. The chunk must be specified as a full path to a device file (e.g. /dev/wd0d). A RAID volume rather than a RAID controller is expected as the final argument.

-t patrol-function

Control the RAID card's patrol functionality, if supported. patrol-function may be one of:

stop

Stop the patrol on the RAID controller.

start

Start the patrol on the RAID controller.

get

Retrieve the current patrol configuration.

disable

Disable the patrol functionality.

manual

Enable the patrol functionality to start/stop manually.

auto[.interval[.start]]

Enable the patrol functionality to start/stop automatically in every interval seconds, starting the first iteration after start seconds.

-u channel:target[.lun]

Instruct the device at channel:target[.lun] to cease blinking, if there is ses(4) or safte(4) support in the enclosure.

-v

Be more verbose in output.

In addition to the relevant options listed above, the options for softraid(4) devices are as follows:

-C flag[,flag[,...]]

Pass flag to bioctl. May be one of:

force

Force the operation; for example, force the creation of volumes with unclean data in the metadata areas.

noauto

Do not automatically assemble this volume at boot time.

-c raidlevel

Create a new softraid(4) volume of level raidlevel. The device must be “softraid0”; it supports multiple volumes.

Valid raidlevels are:

0

RAID 0: A striping discipline.

1

RAID 1: A mirroring discipline.

5

RAID 5: A striping discipline with floating parity chunk.

C

CRYPTO: An encrypting discipline.

c

CONCAT: A concatenating discipline.

1C

RAID 1 + CRYPTO: An encrypting and mirroring discipline.

The CONCAT discipline requires a minimum of one chunk, RAID 0 and RAID 1 disciplines require a minimum of two chunks, RAID 5 requires a minimum of three chunks and the CRYPTO discipline requires exactly one chunk to be provided via -l.

The RAID 1C discipline requires a minimum of two chunks when a new volume is created, and a minimum of one chunk when an existing volume is assembled. Missing RAID 1C chunks will be marked as offline and must be rebuilt before they become part of the array again.

-d

Detach volume specified by device.

-k keydisk

Use special device keydisk as a key disk for a crypto volume.

-l chunk[,chunk[,...]]

Use the chunk device list to create a new volume within the softraid(4) framework. Requires -c.

-O chunk | channel:target[.lun]

Set the state of chunk or channel:target[.lun] to offline. The state of the RAID volume will change in the same way that it would if the disk physically went offline. The chunk must be specified as a full path to a device file (e.g. /dev/wd0d). A RAID volume rather than a RAID controller is expected as the device argument.

-P

Change the passphrase on the selected crypto volume.

-p passfile

Passphrase file used when crypto volumes are brought up. This file must be root owned and have 0600 permissions.

-r rounds

The number of iterations for the KDF algorithm to use when converting a passphrase into a key, in order to create a new encrypted volume or change the passphrase of an existing encrypted volume. A larger number of iterations takes more time, but offers increased resistance against passphrase guessing attacks. If rounds is specified as "auto", the number of rounds will be automatically determined based on system performance. Otherwise the minimum is 4 rounds and the default is 16.

-s

Read the passphrase for the selected crypto volume from /dev/stdin rather than /dev/tty. This option cannot be used during the initial creation of the crypto volume.

# bioctl -c 1 -l /dev/sd2e,/dev/sd3e,/dev/sd4e,/dev/sd5e softraid0

# bioctl -c C -l /dev/sd2e softraid0

# dd if=/dev/zero of=/dev/rsd3c bs=1m count=1

# bioctl -d sd2

# bioctl -R /dev/wd0d sd0